FrameParser Properties

Properties

CalculatePhaseEstimates Gets or sets flag that determines if current and voltage phase estimates, frequency and dF/dt should be calculated for PoW data.
CalculationFrameRate Gets or sets the configured frame rate for phase estimate calculations.
CanRead Gets a value indicating whether the current stream supports reading.
(Inherited from BinaryImageParserBase)
CanSeek Gets a value indicating whether the current stream supports seeking.
(Inherited from BinaryImageParserBase)
CanTimeoutGets a value that determines whether the current stream can time out.
(Inherited from Stream)
CanWrite Gets a value indicating whether the current stream supports writing.
(Inherited from BinaryImageParserBase)
CheckSumValidationFrameTypes Gets or sets flags that determine if check-sums for specified frames should be validated.
(Inherited from FrameParserBaseTFrameIdentifier)
ConfigurationFrame Gets or sets current IConfigurationFrame used for parsing IDataFrame's encountered in the data stream from a device.
(Overrides FrameParserBaseTFrameIdentifierConfigurationFrame)
ConnectionParameters Gets or sets any connection specific IConnectionParameters that may be needed for parsing.
(Overrides FrameParserBaseTFrameIdentifierConnectionParameters)
Enabled Gets or sets a boolean value that indicates whether the frame image parser is currently enabled.
(Inherited from FrameImageParserBaseFrameType, ISupportSourceIdentifiableFrameImageSourceChannel, FrameType)
EnableIntervalAveraging Gets or sets a flag that determines if interval averaging (boxcar averaging) is enabled across each publish interval when down-sampling.
EnablePublishEMA Gets or sets a flag that determines if an additional exponential moving average (EMA) is applied to the published stream (after interval averaging).
Length The parser is designed as a write only stream, so this method is not implemented.
(Inherited from BinaryImageParserBase)
Name Gets the name of BinaryImageParserBase.
(Inherited from BinaryImageParserBase)
NominalFrequency Gets the nominal LineFrequency of the SEL CWS device.
Position The parser is designed as a write only stream, so this method is not implemented.
(Inherited from BinaryImageParserBase)
ProtocolSyncBytes Gets or sets synchronization bytes for this parsing implementation, if used.
(Inherited from BinaryImageParserBase)
ProtocolUsesSyncBytes Gets flag that determines if SEL CWS protocol parsing implementation uses synchronization bytes.
(Overrides ProtocolUsesSyncBytes)
PublishAnglesTauSeconds Gets or sets the EMA time constant τ (seconds) for published phase angles.
PublishFrequencyTauSeconds Gets or sets the EMA time constant τ (seconds) for published frequency.
PublishMagnitudesTauSeconds Gets or sets the EMA time constant τ (seconds) for published RMS magnitudes.
PublishRocofTauSeconds Gets or sets the EMA time constant τ (seconds) for published ROCOF (dF/dt).
QueuedBuffers Gets the total number of buffers that are currently queued for processing, if any.
(Inherited from MultiSourceFrameImageParserBaseSourceChannel, FrameType, ISupportSourceIdentifiableFrameImageSourceChannel, FrameType)
QueuedOutputs Gets the total number of parsed outputs that are currently queued for publication, if any.
(Inherited from FrameImageParserBaseFrameType, ISupportSourceIdentifiableFrameImageSourceChannel, FrameType)
ReadTimeoutGets or sets a value, in milliseconds, that determines how long the stream will attempt to read before timing out.
(Inherited from Stream)
RecalculationCycles Gets or sets the number of nominal cycles between full DFT recalculations for numerical stability.
RedundantFramesPerPacket Gets the number of redundant frames in each packet.
(Inherited from FrameParserBaseTFrameIdentifier)
ReferenceChannel Gets or sets the reference channel for frequency tracking.
RepeatLastCalculatedValueWhenDownSampling Gets or sets flag that determines if last value should be repeated when down-sampling, i.e., when CalculationFrameRate is less than SEL CWS frame rate (commonly 3000Hz); otherwise NaN will be used.
RunTime Gets the total amount of time, in seconds, that the BinaryImageParserBase has been active.
(Inherited from BinaryImageParserBase)
SampleFrequencyTauSeconds Gets or sets the EMA time constant τ (seconds) for the internal per-sample frequency smoothing that occurs inside the estimator before any down-sampling/publish filtering.
SampleRocofTauSeconds Gets or sets the EMA time constant τ (seconds) for the internal per-sample ROCOF smoothing (computed from the internally smoothed frequency).
Status Gets current descriptive status of the FrameParserBaseTFrameIdentifier.
(Inherited from FrameParserBaseTFrameIdentifier)
TargetCycles Gets or sets the number of nominal cycles contained in the sliding DFT analysis window.
TotalProcessedBuffers Gets the total number of buffer images processed so far.
(Inherited from BinaryImageParserBase)
TrustHeaderLength Gets or sets flag that determines if header lengths should be trusted over parsed byte count.
(Inherited from FrameParserBaseTFrameIdentifier)
ValidateCommandFrameCheckSum Gets flag based on CheckSumValidationFrameTypes property that determines if command frames are selected for check-sum validation.
(Inherited from FrameParserBaseTFrameIdentifier)
ValidateConfigurationFrameCheckSum Gets flag based on CheckSumValidationFrameTypes property that determines if configuration frames are selected for check-sum validation.
(Inherited from FrameParserBaseTFrameIdentifier)
ValidateDataFrameCheckSum Gets flag based on CheckSumValidationFrameTypes property that determines if data frames are selected for check-sum validation.
(Inherited from FrameParserBaseTFrameIdentifier)
ValidateHeaderFrameCheckSum Gets flag based on CheckSumValidationFrameTypes property that determines if header frames are selected for check-sum validation.
(Inherited from FrameParserBaseTFrameIdentifier)
WriteTimeoutGets or sets a value, in milliseconds, that determines how long the stream will attempt to write before timing out.
(Inherited from Stream)

See Also